like 200 i Manuel atelier : Page 114

          12. FUEL SYSTEM                                                                                                      LIKE 200i

 FAILURE CODE LIST
          Failure
 Blinks                        Fault Description           Priority                     Fault Management
          Codes
                                                                      1.Stop immediately and check CELP code.
                                                                      2.Check engine thermo sensor wiring and
                                                                      connections.
   1      P0217     Engine Overheating                        1       3.Check engine lubrication and cooling systems.
                                                                      4.Check engine ignition and fuel systems.
                                                                      5.Extended periods of riding can cause engine
                                                                      overheating
                                                                      1.Check Crank Position Sensor(CPS) wiring and
                                                                      connections.
                                                                      2.Check CPS tp flywheel gap (0.6mm-1.2mm).
   2      P0335     Crank Position Sensor (CPS) Fault         2
                                                                      3.Check crankshaft runout.
                                                                      4.Use ohm meter to check circuit resistance (100-130
                                                                      ohms with engine cool).
                                                                      1.Use KYMCO AFI Diagnostic Tool to reset code.
                                                                      Ensure TPS is within specs. (With throttle plate closed-
                                                                      0.68 volts +/- 0.03 volts).
   3      P1120     Throttle Position Sensor (TPS) Fault      2
                                                                      2.Check TPS wiring and connections.
                                                                      3.Ensure that TPS value to be 0% when throttle plate
                                                                      is closed.
                                                                      1.Check TPS wiring and connections.
                                                                      2.Use KYMCO AFI Diagnostic Tool to measure voltage
                    Throttle Position Sensor (TPS)                    ( below 0.5 volts).
   4      P1121                                               2
                    output is abnormal                                3.Ensure that TPS screw has not been adjusted
                                                                      unnormally, TPS should be 0% when throttle plate is
                                                                      closed.
                                                                      1.Check TPS wiring and connections.
                                                                      2.Use KYMCO AFI Diagnostic Tool to measure voltage
                    Throttle Position Sensor Velocity                 ( below 0.5 volts).
   5      P1122                                               2
                    Fault                                             3.Ensure that TPS screw is adjusted to 0% when
                                                                      throttle plate is closed.
                                                                      4. Replace TPS sensor
                                                                      1.Using volt meter, check battery voltage (12-15 volts).
                                                                      2.Using volt meter, check stator output (13.5-14.5
   6      P0560     Battery Voltage abnormal                  1       volts).
                                                                      3.Check black, blue, and red wires on ECU for shorts.
                                                                      4.Check battery condition.
                                                                      1-Check IAT wiring and connections.
   7      P0110     Inlet Air Thermosensor (IAT) Fault        2       2-Using Ohm meter, check IAT resistance (2554-568.9
                                                                      ohms within 20~60 degree centigrade).
                                                                      1.Check IABV wiring and connections.
                                                                      2.Using Ohm meter, check IABV resistance (24.7-27.3
   8      P0410     Idle Air Bypass Valve (IABV) Fault        2
                                                                      ohms).
                                                                      Note-IABV is powered by the battery
                                                                      1-Check idle bypass valve opening is within specs.
                                                                      (brand new: above 35 degree used: <180 degree)
                                                                      2.Check throttle body for carbon deposits.
                                                                      3.Check Idle Throttle Valve for sticking and check
   9      P0505     Idle Air Bypass Control Range Fault       2
                                                                      adjustment of screw.
                                                                      4. Check intake for air leaks
                                                                      5. Replace the IABV
                                                                      6. Note-IABV is powered by the battery
                                                                      1.Use ohm meter to measure resistance (13.78-15.23
                                                                      ohms.
  10      P0251     Fuel Injector Fault                       2       2.Check injector wiring and connections.
                                                                      3.Check battery wiring and connections.
                                                                      Note-Fuel Injector is powered by battery
                                                                      1.Verify ignition is within specs (0.57-0.66 ohms)
  11      P0350     Ignition Coil Fault                       2       2.Check wiring and connections.
                                                                      3.Check condition of battery wiring and connections.


                                                                                                                        12-8